14mz, Instruction manual • Read online or download PDF • Futaba 14MZ User Manual. Get Futaba 14MZ Manual. Get all Futaba manuals! 14MZ. 14 CHANNEL RADIO CONTROL SYSTEM. PCMG3/PCM/FM selectable. INSTRUCTION. Compact Flash (CF) Card Handling Instructions Follow these precautions when handling the CF card included in your 14MZ transmitter. DO NOT allow the.
|Country:||Saint Kitts and Nevis|
|Published (Last):||13 April 2010|
|PDF File Size:||6.9 Mb|
|ePub File Size:||15.66 Mb|
|Price:||Free* [*Free Regsitration Required]|
Servo connection by model type The T14MZ transmitter manuak are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu. Home screen Here is the home screen and its descriptions.
Flap Setting Flap setting mabual model type]: Call the setup screen by pressing the function you want to set up. Set throttle cut with the Throttle Cut function of the Linkage Menu. However, please note that you can enable or nanual cookies by following the instructions of your browser.
EP glider, general This function lets you set the operation speed when the motor of kanual F5B or other EP glider is started by switch. The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and pushrods are hooked up. Futaba’s original CF cards. Do not expose the CF card to dirt, moisture, water or fluids of any kind.
Close and lock the battery cover until you hear a snapping sound. Don’t have Internet access? The preset elevators and flaps camber flap, brake flap offset amount can be activated by a switch.
Perform this setting when you purchase the set and when adjustment is necessary.
You can adjust the LCD contrast and the backlight brightness, and can change the duration time to turn off the backlight and color of the background by the screen setting in the system menu.
41mz you want you can disable cookies from Google Analytics. Page 83 Flap setting [Corresponding model type]: Use the adjustment buttons to set the delay.
Function Channel assignment of each function can be changed. Touch the button of the function you want to set.
Page Curve setting operation This section describes the setting procedure of curves which are msnual with the AFR function and each mixing function. Adjust the backlighting brightness with the left and right side buttons. Flight condition addition This is convenient when calling a model after registering the model names in advance.
Idle down – Futaba 14MZ User Manual
Do not use the transmitter as it is, send it back for a check to the Futaba Service Center. When you begin to set up a model, be sure that the digital trims are set to their center position. To change the trim rate, you must activate 14jz through the function menu, within the linkage menu.
Always read [Precautions when mounting the receiver and servos] of [Before using]. You can use manuap toolbox contained in the set for various adjustment of the transmitter.
Futaba 14MZ : Manual
Always charge Li-Ion batteries in a fireproof location. When you are using a new PCMG3 receiver and changing the frequency, set ID or frequency by the following instructions. In addition, when the trim position returns to the center, the tone will change.
Push the “Yes” button after confirming the ID. Sub-trim Sub-Trim Setting of neutral position manua, each servo. Touch “Calibration” button and then press “Yes”, the calibration screen will pop up. Return to Home screen System Menu functions table [Trainer]: Page Snap Roll [Corresponding model type]: This is used for testing servo movement.
What’s missing? Tell us about it.
If you need to resend the data, push the “Resend” button. Ailevator [Corresponding model type]: In this case, the same contents are input to the other conditions set in the group mode. Curves which are symmetrical to the left and right of manuzl can also be mqnual. Throttle Hold Example of use This function sets the throttle cut position at auto rotation dive. How to protect the receiver from vibration and water Mounting servos Use a vibration-proof rubber such as rubber grommet under a servo when mounting the servo on a servo mount.
This allows use for switching during training. Open the dust protection cap on the back of the transmitter that is covering the hole for throttle stick adjustment. Disconnect the connectors of switches you want to change. The product is subject to regulations of the FCC and is restricted under United States law to such purposes. The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and pushrods are hooked up.
This time can be set up to 1 hour in 10 minutes increments. Gyro mixing This function used to adjust gyro sensitivity.