AT91SAMQU Microchip Technology / Atmel ARM Microcontrollers – MCU 2x4kB SRAM MHz – PWM datasheet, inventory, & pricing. AT91SAMEK Microchip Technology / Atmel Development Boards & Kits – ARM Eval and code dev f/AT91SAM device datasheet, inventory, & pricing. AT91SAM Supported by the Crossware Development Suite for ARM Professional Edition. Graphical Code Creation Wizards: A/D Converter (ADC); Chip.
|Published (Last):||2 April 2007|
|PDF File Size:||7.97 Mb|
|ePub File Size:||9.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
Remember the log in the main window? If you already created this ag91sam9260 before and modified any of the samples, your changes will get lost. Arduino and List of Arduino boards and compatible systems. Requirements In the first place we need the target board. In the summer these parts were still sampling, and a development board had recently been made available. The easiest way to create such a directory is to let the Configurator create one.
On the first page, titled Repository you can specify the path of at91ssm9260 repository file. Amber open FPGA core. Embedded system Programmable logic controller.
AT91SAMQU Microchip / Atmel | Ciiva
This page was last edited on 17 Decemberat HiSilicon Kirin Qualcomm Snapdragon Check the displayed paths again and click OK. Software development can be done on a Windows or Linux system. After loading the selected configuration, a component tree and a log window appear in the Configurator’s main window.
Check the output in the log window. Open a command line window, for example by executing cmd. The amount of documentation for all ARM chips is daunting, especially for newcomers. Double click on the file events. You should now see some output in the terminal emulator’s output window.
However, at the time of this writing, only Windows had been fully tested for this CPU. A tabbed dialog with four pages appears. Computer science portal Electronics portal. First some Configurator settings need to be specified. It is recommended to stick with the defaults shown.
The Configurator typically starts with a file selection dialog, from which you can choose a pre-configuration for a specific board.
If the wrong repository had been loaded, you at91samm9260 correct this here. On the third page the build environment has to be specified. You may chose Yes and let the Configurator adapt the new installation path or select No and correct the path later. Always use Unix like slashes to separate directory paths, not Windows like backslashes. For now, just continue.
A confirmation dialog appears, which unfortunately doesn’t clearly state the risk. You may click the button Compare sent file with memory to make sure, that the upload really worked.
ATMEL AT91SAM9260 ARM SOM
Start a terminal emulator like Hyperterm Windows default or TeraTerm much better. On Linux, simply enter nutconf on the shell prompt. We will now change to an evironment you may not be used too, the Windows command line.
If you upgraded from a previous version, the following message might be presented on its first start. Don’t worry, nothing really complicated going to happen. Atme, the log window to make sure, that the repository and the configuration file had been loaded from the current installation directory. In order to start the uploaded code, enter go 0x in the script window. Thus no specific programming hardware is required to at91sam99260 the final application into the on-chip flash memory. Archived from the original on A typical top-down documentation tree is: Serial port settings are ,8,n,1.
Microcontrollers have internal program memory as well as the conventional internal registers and RAM. All articles with dead external links Articles with dead external links from October Articles with permanently dead external links. If not correct, you may reload the configuration later.
In a first at91asm9260 the build directory will be prepared. Hardware Firmware Tools Download Community. The last page provides a temporary solution to the currently not existing application wizard.
Creating this directory manually will fix this problem. It may take some time to finish. Expand the PATH environment, change to the directory that contains our events sample and clean-up any previous build by typing the follwing three commands. These settings are stored in the Windows repository.
Atmel ARM-based processors – Wikipedia
Finally terminate the Configurator. This way the correct repository will be loaded. One is in Intel hex format events.