View Notes – dac interfacing with from ELECTRICAL EE at Engineering College. MICROCONTROLLER INTERFACING WITH DAC Sample code for Digital to Analog converter โ€“ DAC interfacing with Following code can be using for and ICs like: 89c DAC circuit using DAC [click to enlarge] LCD Interfacing code (In 4bit mode) + Proteus Simulation ยท Interfacing with UART of.

Author: Dor Tojagar
Country: Nepal
Language: English (Spanish)
Genre: Video
Published (Last): 11 November 2013
Pages: 410
PDF File Size: 8.28 Mb
ePub File Size: 3.92 Mb
ISBN: 401-1-85743-496-9
Downloads: 40377
Price: Free* [*Free Regsitration Required]
Uploader: JoJojin

Microcontroller keep sending data from 0x05 to 0xFE and when this data become 0xFF, it comes out from loop and we are getting Inetrfacing output due to this loop. Tyep ethis program in keil version 2 and generate HEX file and download indidually to get square wave. I picked up one module which we use for our client.

This microcontroller is easily programmable via serial port COM port using FlashMagic utility This utility can be downloaded from link www. Arduino based GPS receiver. In this code, we write separate void delay int time function.

Choosing Battery for Robots. Skip to main content.


The digital data coming from microcontroller is converted to analog by DAC We can also keep WR pin enable all the time where we need to give 8 bit output data to DAC frequently. Above program is very simple to understand. Digital data is coming from microcontroller. You can interfwcing V supply in the circuit. See Example for verification of the calculations. Interface GPS with Arduino. Therefore, an 8-input DAC. Log in or register to post comments.


Type the following program in evaluation keil version cross compiler. What is Web Browser. Therefore, to achieve the full-scale 10 V output, we use the following equation. This method ensures that only integer numbers are output to the DAC by the microcontroller.

How to configure DAC? This high-density System-in-Package SiP integrates controller, power switches, and support components. Generating a sine wave.

Digital to Analog converter โ€“ DAC interfacing with 8051

The I re f current is generally set to 2. Then we demonstrate how to generate a sine wave on the scope using the DAC. Interfacing of IC with 89s52 microcontroller is shown in Fig3. In real life, however, this interfaving cause inaccuracy since the input resistance of the load where it is connected will also affect the output voltage.

Saeed’s Blog: DAC (using DAC) code + Proteus simulation

This site uses cookies. You type following program in evaluation keil version cross compiler. In embedded market independent DAC modules are available for ingerfacing.

The output of the DAC is given to the op amp which works as current to voltage converter. Ideally we connect the output pin I out to a resistor, convert this current to. This section will show how to interface a DAC digital-to-analog converter to the DAC output is connected to op amp which works as current to voltage converter.

Above program is very easy to understand. I picked up one module which we have used for our client. Then write a program to send data to the DAC to generate a stair-step ramp. The values for the sine function vary from After incrementing the value of P1 in first loop and decrementing it in the second loop, we get triangular waveform as shown in Fig 6.


Exclusive Digi-key Tools Embedded computers. Angle 9 degrees Sin 0.

DAC Interfacing – Microcontroller Course

Special circuitry provides TTL logic input voltage level compatibility. The total current provided by the I out pin is a function of the binary numbers at the DO โ€” D7 inputs of the DAC and the reference current I re fand is as follows: By continuing to use this website, you agree to their use. In second loop we are decrementing value using. Next post i will be discussing about instructions calculation to send data to microcontroller.

Table shows the angles, the sine values, the voltage magnitudes, and the integer values representing the voltage magnitude for each angle with degree increments.

Email required Address never made public. You are commenting using your Facebook account. In order to generate a stair-step ramp, set up the circuit in Figure and connect the output to an oscilloscope.