IAME PARILLA X30 MANUAL PDF

View and Download IAME Parilla X30 cc RL overhaul manual online. Parilla X30 cc RL Engine pdf manual download. Also for: Parilla x View and Download IAME Parilla x30 cc RL-TaG assembly instructions & user manual online. Parilla x30 cc RL-TaG Engine pdf manual download. Stay connected to IAME’s social network and become a member of the IAME community. Enjoy videos and pictures; learn about upcoming events, and countless.

Author: Keshakar Samugami
Country: Ecuador
Language: English (Spanish)
Genre: Marketing
Published (Last): 20 May 2016
Pages: 465
PDF File Size: 6.1 Mb
ePub File Size: 10.71 Mb
ISBN: 871-6-15502-564-9
Downloads: 75291
Price: Free* [*Free Regsitration Required]
Uploader: Gardalar

Start with an adjustment on the rich side. Use of different spark plugs is possible and, as a general information, we are attaching a correspondence list among spark plug of other brands, based on thermal degree which represents the capacity of the spark plug to dissipate the internal heat. The following prailla, if carefully followed, will allow a long clutch life.

Install The Water-cooling System 2. To install the water pump belts paarilla is necessary to remove the rear axle.

Never exceed the above limit.

Page 33 The following example should clarify the procedure for the optimization of the sprocket ratio. No obligation of Parikla exists in case the above limit is exceeded. Use of fuses with higher amperage might damage the electronic box whenever the battery polarity is reversed. Page of 47 Go. In case of breakage, replace the broken spring. When designing this new engine, we have considered the technical solutions already adopted for the high performance engines, and the experience acquired with the TaG engines Touch and Go.

  DISKURSENS ORDNING PDF

IAME PARILLA X30 CC RL OVERHAUL MANUAL Pdf Download.

This is a 3 position key: Page 32 According to the different engine versions. In order to lenghten the battery life it is necessary though to follow a few recommendations: Seal with tape the engine inlet and exhaust. Warm the engine gradually for about 5 minutes at half throttle, making some laps at low speed, gently closing and opening the carb. When the tension drops below Got it, continue to print.

The following example should clarify the procedure for the optimization of the sprocket ratio.

L close the screw completely and then open: It is necessary to recharge the battery. Always make sure that the springs are well hooked and in place.

In case the engine is supplied already assembled on the chassis, it is at care of the assembler to follow these instructions. In case the flexible is damaged, metallic particles could be sucked in the engine and cause a seizure.

IAME Parilla 60cc Baby Assembly Instructions And User’s Manual

Replacement Of The Starter Brushes 4. Don’t show me this message again.

The final customer, in this case, can skip this section and can start reading from section 3. Disconnect the battery and charge it periodically see sect.

Manuals | IAME KARTING

Don’t have an account? Table of Contents Add to my manuals Add.

  DIABETE GESTAZIONALE LINEE GUIDA 2010 PDF

Exhaust Header Assembly Fig. According to the different engine versions. The external of the engine must be cleaned. For a correct installation follow the under shown instructions. Install The Intake Silencer 2. Comments to this Manuals Your Name. When starting the engine, make sure that the brake pedal is fully pressed to avoid sudden accelerations. Only use 5A strip fuse.

The engine is suplied without oil in the gear box. Contents of packing 1. Enter text from picture: Before assembling the clutch, wash with diluent the shaft taper, the connecting hole on the clutch body, the clutch drum and the starter ring. To print the manual completely, please, download it.

Before starting the engine fill the box with SAE 30 oil.

IAME X30 Technical Information

In case the user wishes to optimize on the track the sprocket ratio in order to achieve the best possible performance, without abusing the engine, follow the under shown recommendations. Gear Timing Schematic Before assembling the clutch, wash with diluent the shaft taper, the connecting hole on the clutch body, the clutch drum and the starter ring. Refer to the following drawing during the operations.